Because I had temp. failure issues with Amber only straight Modules, I first purchased 2 amber thin bars to cut into 4 shorter lights to use as separate running & turn signal front lights on the motorcycle fairing side edges instead. I first tested the thin bars at both -20 & +120 degrees F with no failures both before & after being cut. I also submersed them in water & snow without any failures also. To obtain a clean look I used 3M trim molding tape to mount the thin bar strips instead of the supplied hardware. I later purchased an amber & red thin bars to resolve a back voltage issue I had with 1157 bayonet LED bulbs in turn signals & brake/Taillight. In normal vehicle applications this is not an issue but on my motorcycle where separate 2 wire LED turn, Brake & running lights are used by tapping off the wires from stop, turn & light switches It was a very noticeable problem. Turning on running lights would activate separate LED Brake lights & activating turn signal would cause flickering in non turn bulbs. I did not have this issue when normal Filament 1157 bulbs were used, only the LED replacements. So I kept the Brake/Taillight bulb non LED and cut the red thin bar into two & mounted on either side of the License Plate bracket as extra brake lights. I disconnected running light wire from bulb contact in front turn signals & connected to cut amber thin bar mounted under bottom leading edge if housing for my running lights with 1157 LED bulbs only one contact bright mode for turning. Again I used 3M tape for clean look. I plan on adding White Thin Bars on the older classic car as daytime running lights as they are small & non visible until turned on. Also in time use Cool White in the house to replace CFL thin lights under kitchen passthrough & In wall office desk. Logical choice since I can go off grid with batteries charged be solar. Your Thin LED Light Bars are rugged, durable, easy to mount out of sight but put out a very bright light comparable to CFL & Halogen bulbs.

I purchased 5 of these units to be used in an experimental aircraft I'm building. The aluminum channel makes these really sturdy and the wiring on both ends of the light really helps to run them in series. These will be a nice addition to my aircraft. I'm attaching to a dimmer circuit and will have these light bars flood lighting the foot wells and baggage compartment. I'm picky and not just anything goes into this aircraft. No hesitation using this product.

Today I installed the Ultra Thin Neutral White led lights and they are a perfect match for my OEM 2020 BMW DRLs. You guys voluntarily address my concerns that the Cool White was too blue and the Warm White was too yellow by manufacturing 5500k-6000K led lights that matches BMW led lights. You guys went above and beyond for customer satisfaction and I appreciate it. Thanks!!!

My vehicle was fitted with custom blue flexible LEDs seven years ago. The strip on the passenger side was failing so I decided to try the Ultra Thin Light Bar as a replacement. The bar is about 1 inch shorter than the old one. Installed it with Velcro in 5 mins. Now I have a new problem..........Ultra Thin LED bar burns brighter than the old flexible strip did! I purchased Piranha bars from Oznium for under cabinet light strips in our kitchen 8 years ago. Sure wish these Ultra Thin models had been available back then. They make the Piranha bars look like military tanks!

I use many different types of LEDs for museum exhibits, and these were very simple to install, as well as very slender so they were easy to hide. I used these strips to light up engine components in an interactive car exhibit in a children's museum. I was able to zip-tie them to some existing tubes and cables and angle them as needed. The length was fine for this installation, but I would like some linger lengths in the future without having to daisy chain them together.

The products work GREAT. I'm using 9 pieces as interior lighting on my duck boat. I used RTV to glue them to the bottom side of my top rail while I supported the wires. I also added a few feet of 18gauge wire to allow plenty of slack in between. All connections were soldered and heat shrinked to protect from the environment. I really appreciate your customer service.

I bought the light bars not knowing the bright light that I would get. I wired ten strips together to create lights for my RV steps. Little did I know that the ten strips would be so great. It created a safe atmosphere for exiting the RV during the dark nights in the mountains. Excellent lights and would buy again.

Used as roll bar dome lights on a Jeep, super bright, love the aluminim. Great added feature. Good double sided tape as well. Great to have the wire be able to come out the back side of the bar for clean install.

We're using these Ultra Thin UV LED Light Bars as under dash/foot well lighting and under seat lighting. They put out a ton of light from such a small light bar!!! I will be buying more for my many other personal vehicles as well!!! I've been using Oznium.com for every LED lighting needs on my own personal vehicles and the thousands of my other customer vehicles as well!!!! I'll never switch lighting need companies!!! Oznium.com is the best!!!

This product, the Ultra Thin LED Light Bar - Blue, was an exact fit for my project needs - to have a high quality product that meets both the ultra thin sizing requirement as well as providing a consistent and vibrant blue color output. This product met both needs extremely well.